BFEC Type Right Angle 2-1/2" Aluminum Alloy Pneumatic Pulse Valve For Dust Collector DMF-Z-62S

BFEC Type Right Angle 2-1/2'' Aluminum Alloy Pneumatic Pulse Valve For Dust Collector DMF-Z-62S

This valve below is DMF-Z-62S right angle type solenoid pulse jet valve with die-casting aluminum alloy body. It simplifies the connection between gas bag and blowing tube of a dust collector. It can provide stronger airflow and meet dust removing requirements.

The high-pressure gas enters from the air inlet , enters the lower air chamber.

1. When the pulse valve is not energized, the gas enters the decompression chamber through the impulse valve and the orifice in the constant pressure pipeline on the upper and lower shells. The valve core blocks the pressure relief hole under the action of the spring. The gas will not be discharged, so that the pressure in the decompression chamber and the lower air chamber are consistent. Under the action of the spring, the diaphragm will block the injection port, and the gas will not burst out.

2. When the pulse valve is energized, the valve core is lifted upward by the electromagnetic force, the pressure relief hole is opened, and the gas is ejected. Due to the role of the orifice of the constant pressure pipe, the outflow speed of the pressure relief hole is greater than that of the decompression chamber. The inflow speed of the pressure pipe gas makes the pressure in the decompression chamber lower than the pressure in the lower chamber. The gas in the lower chamber lifts up the diaphragm, opens the injection port, and performs gas injection.

Specification Of DMF-Z-62S Electromagnetic Pulse Jet Valve:

Overall Diemension

Deconstruction Diagram

Flow Direction Of DMF-Z-62S:

FAQ:

1.During installation and commissioning

1). The valve cannot be opened, but the pilot is operating. → Check if the airbag pressure is too low → Exclude air leaks.

2). Some valves are not working, others are normal.→Check the valve's wiring link and solenoid coil. → Replacement of accessories.

3). The valve cannot be closed and there is a leak, pressure cannot be established. → The inlet of the valve is installed opposite the injection port. → reassemble

4). The valve cannot be closed and there is a leak. → Impurities are adsorbed on the diaphragm, and the iron core is stuck. →Clean the diaphragm, check whether the diaphragm is complete, check the iron core, and replace the parts in time.

2.During use

1). Valve closes slowly. → Diaphragm orifice blocked. →Dredge orifice.

2). Some valves leak, the diaphragm does not close,normally opened. → Impurities are adsorbed on the diaphragm, the pilot is damaged, and the iron core is stuck. → Clean the diaphragm, check whether the diaphragm is complete, check the iron core, and replace the parts in time.

3). The coil is hot and burned. → Power on for a long time. → Check the working condition of the control system.

4). There is voltage but the valve is not working. → Damaged diaphragm or blocked orifice. → Replace parts in time.

5). Low ambient temperature, the valve is leaking or cannot be opened. → Ambient temperature is too low, there is icing in the valve. → Note the valve operating temperature range.

Welcome to your any question and inquiry!

* Foucus on your demand, Offer you best solutions as the first mission of Ningbo Brando Hardware Co., Ltd, we work on designing and manufacturing solenoid coils, solenoid armatures and solenoid valves for more than 15 years.   * We have served customers from Europe, North America, Middle east, Southeast Asian by designing and manufacturing for their automation fluid control applications, related to industries of pneumatic automation equipment, food beverage dispenser, agricultural irrigation, printing and dyeing, dust collector, home appliance, automobile, textile, refrigeration, etc.

* Since the company's inception, we are dedicated to providing high quality products and service to our customers. With focusing on our customers' demands, at before production we discuss technical points according to applications with customers to reduce mistake and save cost for both sides. During production, we use high precision CNC machine, machining center to control dimensions and improve productivity. At beginning and mid of machining, our senior inspectors check quality regularly by recording data on documents as per ISO9001 management system. Before shipment, our staff make testing and complete inspection one piece by one piece to ensure the products without defect when reached our customer's hands.

* Ningbo Brando Hardware Co., Ltd will offer you best service with fast response, let's make the fluid control application more widely and smartly.

Product Categories:

1. Solenoid Valve
2. Solenoid Coil
3. Solenoid Armature
4. Solenoid Coil Connector
5. Solenoid Valve Timer
6. Pulse Valve
7. Valve Diaphragm
8. Pulse Controller
9. Refrigeration Valve
10. Pneumatic Valve
11. Pneumatic Fitting
12. Pneumatic Cylinder
13. Pneumatic Filter Regulator Lubricator
14. Pneumatic Vibrator
15. Ball Valve
16. Butterfly Valve
15. and so on