EVI 3P/16 AMISCO Type Hydraulic Solenoid Coil DIN 43650A DC24V AC220V 16mm x 37.5mm x 50mm

EVI 3P/16 AMISCO Type Hydraulic Solenoid Coil DIN 43650A DC24V AC220V 16mm x 37.5mm x 50mm

This EVI 3P/16 AMISCO Type Hydraulic Solenoid Coil is used in hydraulic check valves. The check valve is used in the hydraulic system to prevent reverse flow of oil flow. It is used in the pneumatic system to prevent reverse flow of compressed air. The fluid can only flow along the inlet, but the outlet medium cannot be recirculated.

Several ways in which the check valve is used in the hydraulic system:
(1) If the check valve is installed at the pump port, it can prevent the pressure rise of the system and damage the oil pump.

(2) If the check valve is in parallel with the throttle valve or the pressure reducing valve, the actuator is fast to the reverse speed; or the reverse flow is reversed to the deceleration.

(3) If the check valve is connected in series with the pressure valve, gradually increase the adjustment pressure to prevent pressure reaction.

(4) For the liquid control check valve, the control oil passage is used, and when the check valve is opened, the oil cannot be reversely flowed back.

Technical parameter of EVI 3P/16 DIN 43650A AMISCO Type Hydraulic Coil:

Main dimension of EVI 3P/16 AMISCO Type DIN 43650A Hydraulic Coil:

Detail enlargement of DIN 43650A EVI 3P/16 Amisco Type Hydraulic Coil:

Physical map of EVI 3P/16 DIN 43650A Amisco Type Hydraulic Solenoid Coil:

More details about EVI 3P/16 AMISCO Type Hydraulic Solenoid Coil in below Youtube Video:

Hydraulic electromagnetic coil technical parameters:
Connection form: quick installation; type: control valve; material: iron; scope of application: all kinds of machinery and equipment; installation form: plate bolt installation; drive mode: electromagnetic; parts and accessories: coil.

Main features of hydraulic solenoid coil:
1. The windings are arranged neatly, and the resistance error between the coils is between 0.5 ohms;
2. The outer diameter tolerance of the product is controlled at 0.1mm;
3. Straight in the armature winding, the armature insulation layer is made of high quality insulating tape without wrinkles;
4. The frame size accuracy reaches 0.01mm, which is convenient for interference fit assembly.

Two common questions about solenoid valve coil:

Question: When the electromagnetic coil is energized, the noise is too large. How to solve it?
Answer: The origin of the electromagnetic coil noise problem lies in the lead head part. The pilot head has the difference of AC and DC. The AC pilot component needs to add a magnetic separation ring on the static iron core, which can effectively control the noise problem.

Question: How should the electromagnetic coil be selected?
Answer: You can find the inner hole size, height and width of the electromagnetic coil to find similar or identical electromagnetic coils.

Electromagnetic coil installation method:
Insert the solenoid into the spool of the solenoid valve and fix it in the correct direction.
The power pin or lead is connected to the two poles of the power supply, and the grounding pin is connected to the grounding wire (in general, the power input is not divided into positive and negative poles, and the special case is connected by the positive and negative signs of the coil).

The reason why the solenoid valve coil is hot:
When the coil of the solenoid valve is in operation (energized), the core is attracted to form a closed magnetic circuit. That is, when the inductance is at the maximum state, the design time. The heat is normal, but the core can not be smoothly connected when the core is energized, the inductance of the coil is reduced, the impedance is reduced, and the current is increased accordingly. This causes the coil current to be too large and the life is affected, so the oil, impurities, deformation, etc. are hindered. When the power is turned on, the action is slow, and even if it is not normally fully absorbed, the coil is often energized with a state in which the impedance is less than normal, which is a factor that causes the coil to heat up.

The confirmation method of the solenoid valve coil is good or bad:
To confirm that the electromagnetic coil is good or bad, you can use the multimeter to measure the resistance of the solenoid valve. The resistance of the coil should be around 1K ohm! If the resistance of the coil is infinite, it means that the circuit is open. If the coil resistance tends to zero, it should be replaced with a new one.

Welcome to your any question and inquiry!

* Foucus on your demand, Offer you best solutions as the first mission of Ningbo Brando Hardware Co., Ltd, we work on designing and manufacturing solenoid coils, solenoid armatures and solenoid valves for more than 15 years.   * We have served customers from Europe, North America, Middle east, Southeast Asian by designing and manufacturing for their automation fluid control applications, related to industries of pneumatic automation equipment, food beverage dispenser, agricultural irrigation, printing and dyeing, dust collector, home appliance, automobile, textile, refrigeration, etc.

* Since the company's inception, we are dedicated to providing high quality products and service to our customers. With focusing on our customers' demands, at before production we discuss technical points according to applications with customers to reduce mistake and save cost for both sides. During production, we use high precision CNC machine, machining center to control dimensions and improve productivity. At beginning and mid of machining, our senior inspectors check quality regularly by recording data on documents as per ISO9001 management system. Before shipment, our staff make testing and complete inspection one piece by one piece to ensure the products without defect when reached our customer's hands.

* Ningbo Brando Hardware Co., Ltd will offer you best service with fast response, let's make the fluid control application more widely and smartly.

Product Categories:

1. Solenoid Valve
2. Solenoid Coil
3. Solenoid Armature
4. Solenoid Coil Connector
5. Solenoid Valve Timer
6. Pulse Valve
7. Valve Diaphragm
8. Pulse Controller
9. Refrigeration Valve
10. Pneumatic Valve
11. Pneumatic Fitting
12. Pneumatic Cylinder
13. Pneumatic Filter Regulator Lubricator
14. Pneumatic Vibrator
15. Ball Valve
16. Butterfly Valve
15. and so on